CNC Machined Aluminium Gearbox & Transmission Cases

Précision Nous sommes spécialisés dans l’ of aluminum gearbox housings, transmission cases, and drivetrain components — from prototype to production. Tolérances down to ±0,005 mm, 3/4/5-axis capability, ISO-certified quality. Serving automotive, industrial machinery, robotics, and aerospace clients worldwide.

Points Clés

• Matériaus: 6061-T6 (general purpose) and 7075-T6 (high-strength) Alliage d'aluminiums — full spec table below
• Capabilities: 3-axis to 5-axis Nous sommes spécialisés dans l’ for housings, covers, bearing seats, and oil passages
• Tolérances: Standard ±0.01 mm, precision ±0,005 mm for bore diameters and gasket surfaces
• Industries: Automotive EV/racing, industrial pumps, robotics actuators, aerospace structures
• Quality: CMM inspection, material certification, surface roughness testing on Chaque lot
• Turnaround: 7-day prototype lead time, no minimum order quantity

Why Aluminium for Gearbox & Transmission Housings

Aluminium is the dominant material for gearbox and transmission cases in modern manufacturing. Compared to cast iron or steel, aluminum offers three decisive advantages for drivetrain components:

• Weight reduction: Aluminium is 65% lighter than steel — critical for automotive Nous sommes spécialisés dans l’ applications where every kilogram affects fuel economy and acceleration. A typical aluminum gearbox housing weighs 4-8 kg versus 12-22 kg in cast iron.
• Thermal management: With thermal conductivity of 150-170 W/m·K (3× that of steel), aluminum gearbox cases act as heat sinks, dissipating friction heat from gears and bearings more efficiently. This reduces oil temperature by 10-15°C in sustained operation.
• Corrosion resistance: The natural aluminum oxide layer provides inherent protection against moisture and road salt — no plating required for most environments. For marine or chemical exposure, hard anodisation adds a 25-50 μm protective layer.
• Machinability: Aluminium’s lower cutting forces (compared to steel or titanium) enable faster cycle times, reducing per-part cost by 30-50% for production volumes. Tool life is 3-5× longer than when machining steel alloys.

Meilleur pour: Automotive EV housings, racing transmission cases, industrial pump bodies, and any application where weight × strength matters.
Avoid when: Extreme wear environments (rock crushers, mining equipment) — consider hardened steel or ductile iron instead.

Alliage d'aluminium Selection for Gearbox Applications

Choosing the right aluminum grade depends on your strength, weight, and corrosion requirements. Below is a comparison of the most common alloys used in gearbox and transmission manufacturing:

For most industrial gearbox applications, 6061-T6 offers the best balance of strength, machinability, and cost. For performance applications where weight savings justify the premium, 7075-T6 delivers near-steel strength at one-third the weight. See our complete aluminum Nous sommes spécialisés dans l’ guide for detailed speed/feed recommendations.

Usinage CNC Capabilities for Drivetrain Components

Gearbox housings demand multi-face machining with tight positional Tolérances between bore centers. Our CNC capabilities cover the full range of complexity:

Meilleur pour: Bore diameters from Ø20 to Ø300 mm, bore-to-bore center distance Tolérances of ±0.01 mm, flatness of 0.02 mm/m on sealing surfaces.
Avoid when: Single-setup 3-axis parts under 100×100 mm — our Tournage CNC service may be more cost-effective for small Pièces rotatives.

Typical Gearbox Parts We Manufacture

Over the past decade, BravoFabs has machined thousands of drivetrain components for clients in 11 countries. The most common parts include:

• Gearbox main housings — Single-piece aluminum bodies with integrated bearing seats, oil galleries, and mounting points. Typical Tolérances: bore Ø ±0.01 mm, flatness 0.02 mm/100 mm.
• Transmission cases (manual & automatic) — Split-case or monoblock designs with internal ribbing for structural rigidity. Common in EV reduction gearboxes and industrial power transmission.
• Bearing housings & retainer plates — Précision-bored seats for ball and roller bearings, often with threaded mounting holes and dowel pin locations for alignment.
• Sliding sleeves & shift forks — Wear-resistant components machined from 7075-T6 with hard-anodized contact surfaces. Typical hardness: 400-500 HV after anodisation.
• Oil pump bodies & valve blocks — Complex internal channels for hydraulic fluid routing, pressure-tested to 20+ bar after machining.
• Differential cases & axle housings — Large-diameter bores with cross-drilled lubrication holes. Often machined from 6061-T6 with post-machining T6 Traitement thermique.
• Custom motor adapter plates — Précision-machined interface plates connecting motors to gearboxes, with dowel holes for alignment and threaded bolt patterns.

Surface Finitiones & Treatments

Post-machining Traitement de surfaces extend the life and performance of aluminum gearbox components:

For transmission cases with internal oil passages, we recommend hard anodisation on all fluid-contact surfaces to prevent erosion from hot oil flow. External surfaces can be left as-machined or anodized for corrosion resistance.

Quality Inspection Procédé

Every gearbox housing undergoes a four-stage inspection protocol before shipment:

1. CMM Dimensional Inspection — Bore diameters, center distances, flatness, and perpendicularity verified to ±0.003 mm using a coordinate measuring machine. Full dimensional reports provided with Chaque lot.
2. Surface Roughness Testing — Gasket sealing surfaces checked with a profilometer. Target: Ra 0.8-1.6 μm for sealing surfaces, Ra 1.6-3.2 μm for non-critical areas.
3. Thread Inspection — Every tapped hole checked with go/no-go thread gauges. Thread classes: 2B/3B (inch) or 6H (metric) as standard.
4. Matériau Certification — Mill test reports (EN 10204 3.1 or equivalent) included with Chaque expédition, verifying chemical composition and mechanical properties of the raw aluminum billet.

For complete quality documentation on our inspection capabilities, see our QC inspection devices guide and Contrôle qualité process overview.

Industries & Applications

• Automotive: EV motor housings requiring tight stator bore Tolérances; racing transmission cases machined from 7075-T6 billet; differential housings for performance vehicles.
• Industrial Machinery: Boîtiers de pompe for hydraulic systems up to 350 bar; compressor bodies with integrated cooling fins; hydraulic valve manifolds with cross-drilled galleries.
• Robotics: Précision joint housings with bearing seats for harmonic drive reducers; lightweight actuator bodies for collaborative robots; motor-gearbox interface plates.
• Aérospatiale : Lightweight aluminum gearbox structures for UAV propulsion systems; aircraft actuator housings meeting AS9100 traceability requirements.
• Marine: Corrosion-resistant outdrive housings with hard-anodized protection against saltwater; propeller shaft bearing carriers in 6061-T6.

Why Choose BravoFabs for Gearbox Machining

We are not a general machine shop — drivetrain components are a core competency. Our ISO 9001 certified facility in Dongguan, China has dedicated fixturing for gearbox-class workpieces and processes refined over 10+ years of Nous sommes spécialisés dans l’ experience.

• ISO 9001 certified facility with full material traceability
• 7-day turnaround on prototypes — from STEP file to first article inspection
• No minimum order — 1 piece prototype to 10,000+ production run
• Free DFM (Conception for Manufacturing) review identifying cost-saving opportunities before cutting metal
• DHL/FedEx/UPS worldwide shipping with full export documentation