Injection Mold Ontwerp Guide: Principles, Materiaals & CNC-bewerking

A practical guide to injection mold design — from part geometry rules to Materiaalkeuze voor mallen. Whether you are designing a new plastic part or optimizing an existing mold for Productie, these principles reduce defects, speed up cycle times, and lower tooling costs. Written for product designers, mechanical engineers, and manufacturing buyers sourcing injection molding tooling.

Belangrijkste conclusies

• Wanddikte: Uniform 1.2-3.0 mm is the #1 rule — variations cause warping and sink marks
• Draft angles: Minimum 1° on untextured surfaces, 3°+ on textured — without draft, parts stick and molds wear faster
• Gate placement: Always gate at the thickest section to ensure complete cavity fill before cooling
• Mold materials: P20 steel for 500K-1M shots, H13 for 1M+, aluminum 7075 for prototypes (5K-10K shots)
• CNC-bewerking: 5-axis precision for complex mold cores — mirror polish down to SPI A-1 for optical parts
• DFM checklist: 7-point verification before tooling starts — downloadable at the end of this guide

1. Wanddikte — De #1 Ontwerpregel

Uniform Wanddikte is the single most important design principle in injection molding. Non-uniform walls cause differential cooling rates — thick sections stay molten while thin sections solidify, creating internal stresses that manifest as warping, sink marks, and voids.

• Recommended Wanddikte range: 1.2 mm to 3.0 mm for most engineering thermoplastics (ABS, PC, PA6, POM)
• Thick-to-thin transitions: use gradual tapers — maximum 3:1 thickness ratio across any transition zone
• Rib thickness: 40-60% of the adjoining Wanddikte to prevent sink marks on the opposite face
• Boss OD: 2× the screw/insert diameter; Wanddikte around boss = 0.6× main wall

Best voor: Structural housings, Elektronische behuizingen, consumer product shells.
Avoid when: Part has unavoidable thick bosses — consider gas-assist molding or structural foam instead.

2. Lossingshoeken — waarom ze belangrijk zijn

Draft angles are the slight tapers added to vertical walls to allow the part to release from the mold without dragging or sticking. Insufficient draft causes three problems: parts stick to the core side (increasing cycle time), ejector pins leave visible marks, and in extreme cases, the mold steel galls and requires repair.

• Untextured surfaces: Minimum 1° draft — but 1.5-2° is safer for Productie
• Textured surfaces (VDI/SPI): Add 1° per 0.025 mm of texture depth — typically 3-5° for medium textures
• Deep cores and tall ribs: 3-5° minimum — ribs taller than 10 mm need aggressive draft to avoid sticking
• Shut-off surfaces: 3-5° to prevent flash and mold damage at parting line interfaces

Best voor: Any vertical wall parallel to mold opening direction.
Avoid when: Cosmetic outer surface with zero draft specification — use a precision CNC machined mold with mirror-polished cavity to reduce sticking at low draft angles.

3. Poortplaatsing & Loperontwerp

The gate is where molten plastic enters the cavity — its location determines fill pattern, knit line positions, and part strength. Poor gate placement causes short shots, excessive warpagina, and visible flow marks on cosmetic surfaces.

• Gate at the thickest section: Ensures the melt front reaches thin areas before solidifying
• Avoid gating near cosmetic surfaces: Gate vestige (the small mark left after degating) should be on non-visible faces
• Multiple gates for large parts: When flow length exceeds 200 mm, add secondary gates to reduce injection pressure
• Submarine (tunnel) gates: Auto-degate during ejection — ideal for high-volume Productie without manual trimming

4. Ondersnijdingen en zijacties

An undercut is any feature that prevents the part from being ejected straight out of the mold — holes perpendicular to the mold opening direction, snap-fit tabs, or recessed grooves. Undercuts require sliding cores or lifters, which add 20-40% to mold cost and increase cycle time door 2-5 seconds per shot.

• Redesign to eliminate: Use pass-through cores (holes open on both sides) or split the part line to align with undercut features
• Lifters for internal undercuts: Angled pins that move during ejection — limited to 10-15 mm travel
• Sliding cores for external undercuts: Hydraulic or cam-actuated — can handle larger travels (up to 100 mm)
• Collapsible cores: For internal threads — expensive but eliminates unscrewing mechanisms

Best voor: Complex enclosures with snap-fits, connector housings with side ports.
Avoid when: Budget is under $5,000 — redesign to eliminate undercuts or accept a 2-piece assembly.

Materiaalkeuze voor mallen

The mold material determines tool life, surface finish quality, and per-part cost. Hoger-grade steels cost more upfront but deliver 10-20× the shot life. For prototype and low-volume Productie, aluminum molds offer faster turnaround at lower cost. At BravoFabs, we CNC machine mold cores from all common Gereedschapsstaalsoorten and Aluminiumlegerings.

Best voor: P20 for 80% of commercial Toepassings. H13 when running glass-filled nylon or PPS. Aluminium 7075 for prototypes and bridge tooling.
Avoid when: Using aluminum for Productie volumes over 10,000 — tool wear becomes the dominant cost.

CNC-bewerking voor precisie matrijskernen

Modern injection molds depend on high-precision CNC-bewerking for the cavity and core inserts. At BravoFabs, we machine mold components from hardened tool steel with Toleranties as tight as ±0,005 mm. Our CNC-bewerking capabilities include:

• 5-axis CNC-bewerking: Complex curved surfaces and deep cavities in a single setup, eliminating alignment errors from multiple setups
• High-speed machining (HSM): 20,000+ RPM spindles for fine detail work on electrodes and direct-machined cavities
• Wire EDM: Sharp internal corners, deep ribs, and features impossible to reach with rotating tools
• Polijsten: Multi-stage diamond Polijsten from SPI B-3 (600 grit) to SPI A-1 (mirror, 3 μm diamond) for optical-grade surface finish
• Texture Etsen: VDI 12 to VDI 45 textures applied post-machining for cosmetic surfaces

Veelgemaakte Ontwerpfouten & Hoe Ze te Vermijden

Productiegericht Ontwerpen (DFM) checklist

Before Verstuuring your Onderdeelontwerp for tooling, verify these seven points. Each missed item can add $500-$2,000 in mold rework and delay Productie door 2-4 weeks.

1. Wanddikte uniform throughout part? — Check with section analysis in CAD. Any section >3× the nominal wall is a sink risk.
2. Minimum 1.5° draft on all vertical surfaces? — Run a draft analysis with parting line defined. Red surfaces (negative draft) = stuck parts.
3. Radii ≥0.5 mm on all internal corners? — Sharp corners concentrate stress and reduce mold life. Add fillets to all internal edges.
4. Gate placement at thickest section? — Mold flow simulation (Moldflow or similar) confirms fill pattern before cutting steel.
5. Undercuts eliminated or accounted for? — Each undercut requires a side action. Add cost estimate: $800-1,500 per side action.
6. Parting line follows simplest geometry? — Complex parting lines increase mold cost and create visible witness lines.
7. Ejector pin locations on non-cosmetic surfaces? — Avoid pin marks on Class A surfaces. Specify acceptable pin locations on the drawing.

For metal components that will interface with injection-molded parts — such as threaded inserts, mounting brackets, or reinforcement plates — see our plaatmetaalbewerking and CNC-bewerking services for complementary manufacturing.