Mecanizado CNC Aluminio: Grades, Speeds & Surface Acabado Guide

Puntos Clave

• 6061-T6 is the default choice for roughly 80% of CNC aluminum machining projects — it balances strength (310 MPa tensile), machinability, weldability, and cost better than any other grade.
• 7075-T6 is nearly twice as strong (503 MPa yield vs 276 MPa) but costs 2–3× more and anodizes with a slight yellowish tint due to its copper content. Specify it only when stress analysis demands it.
• Aluminio machines 3–4× faster than steel — carbide tooling runs at 800–1,500 SFM (244–457 m/min), which is why machining cost per part is so competitive.
• Ra 3.2 µm is the standard as-machined finish; tighter finishes (Ra 1.6 or 0.8 µm) add cost and should only be specified on functional surfaces.
• anodizado Type II (1.8–25 µm) is for color and corrosion protection; Type III hardcoat (13–150 µm) is for wear resistance — they are not interchangeable.
• Grade choice drives 20–40% of part cost. Enviaring your drawing for a DFM review before ordering usually pays for itself.

CNC aluminum machining is the workhorse of modern manufacturing: Aleación de aluminios account for more machined parts worldwide than any other metal. They cut fast, hold tight Tolerancias, resist corrosion, and weigh roughly one-third as much as steel. But “aluminum” is not one material — the difference between 6061, 7075, 2024, 5052, and 6082 can mean a 2–3× swing in material cost, a failed anodizado batch, or a bracket that cracks in service.

This guide compares the five most-used aluminum grades for mecanizado CNC, gives realistic cutting-speed data, explains your surface finish options, and shows you how to pick the right grade for your part the first time.

Grade	Mejor para	Tensile / Yield (MPa)	Relative Cost
6061-T6	General parts, enclosures, fixtures	310 / 276	$ (baseline)
7075-T6	Aerospace, high-stress structural	572 / 503	$$$ (2–3×)
2024-T4	Fatigue-critical aircraft parts	469 / 324	$$$
5052-H32	Chapa Metálica, marine, forming	228 / 193	$
6082-T6	EU structural (EN standard)	310 / 250–260	$

Por qué el aluminio domina el mecanizado CNC

Three properties make aluminum the most machined metal in job shops worldwide:

• Machining speed. Aluminio cuts at 3–4× the surface speed of mild steel and up to 10× that of stainless. Faster cutting means less spindle time, and spindle time is what you pay for in mecanizado CNC services.
• Strength-to-weight ratio. At ~2.7 g/cm³, aluminum is about one-third the density of steel. Grades like 7075-T6 approach the strength of some structural steels at a fraction of the weight.
• Built-in corrosion resistance. Aluminio forms a natural oxide layer instantly. anodizado thickens this layer for even better protection — no Pintura or plating required.

The practical result: an aluminum prototype or Producción part is usually quoted 30–50% cheaper than the same geometry in Acero inoxidable, with lead times measured in days instead of weeks.

Aluminio Grades Compared: 6061, 7075, 2024, 5052 & 6082

The table below summarizes the mechanical and processing characteristics that actually matter when specifying a machined part. Values are typical room-temperature figures from ASM/MatWeb material data sheets.

Property	6061-T6	7075-T6	2024-T4	5052-H32	6082-T6
Tensile strength (MPa)	310	572	469	228	310
Yield strength (MPa)	276	503	324	193	250–260
Machinability	Good	Good	Good	Fair (gummy)	Good
Weldability	Excelente	Poor	Poor	Excelente	Good
Corrosion resistance	Good	Fair (SCC risk)	Poor (clad often used)	Excelente (marine)	Very good
anodizado response	Excelente	Good (yellowish tint)	Fair	Excelente	Excelente
Aplicaciones típicas	Enclosures, fixtures, brackets	Aircraft fittings, molds, racing	Fuselage, wing structures	Tanks, panels, marine	EU machine frames, rails

6061-T6 — The All-Propósito Workhorse

6061-T6 is a magnesium-silicon alloy and the default answer to “which aluminum should I use?” It machines cleanly, welds better than any other high-strength grade, anodizes with consistent color, and is stocked everywhere in plate, bar, and extrusion. With 310 MPa tensile / 276 MPa yield strength, it covers electronics enclosures, jigs and fixtures, robot arms, Cuerpos de válvula, and turned shafts — parts we also produce on our Torneado CNC service line daily.

Mejor para: 80% of machined parts — enclosures, brackets, fixtures, prototypes, low-to-medium stress structural components.
Avoid when: yield strength above ~276 MPa is required — step up to 7075 instead.

7075-T6 — Aerospace-Grade Strength

7075-T6 is a zinc-alloyed grade with 572 MPa tensile / 503 MPa yield strength — nearly double 6061-T6, approaching many structural steels at one-third the weight. It chips beautifully on the machine and holds excellent Tolerancias. The trade-offs: material cost typically runs 2–3× that of 6061, it is not recommended for Soldadura, it is more susceptible to stress corrosion cracking in harsh environments, and its high copper content gives clear anodized coatings a slight yellow/smoky tint. Use it for aircraft fittings, high-load brackets, racing components, and injection mold cores.

Mejor para: weight-critical, high-stress parts where FEA justifies the premium — aerospace, robotics, motorsport.
Avoid when: the part needs Soldadura, perfect cosmetic anodizado, or 6061 already meets the load case — don’t pay 3× for strength you won’t use.

2024-T4 — Fatigue Resistance for Aerostructures

2024-T4 is a copper-alloyed grade (469 MPa tensile / 324 MPa yield) prized for one property above all: fatigue resistance under cyclic loading. That is why it remains a standard for aircraft fuselage skins and wing tension members. The copper that gives 2024 its fatigue performance also makes it the least corrosion-resistant grade in this list — it is frequently supplied clad with pure aluminum (“Alclad”) and is rarely welded. For machined parts, specify 2024 when your Aplicación sees millions of load cycles; otherwise 6061 or 7075 is more economical.

Mejor para: fatigue-critical aerospace and transport structures with cyclic loading.
Avoid when: the part faces moisture or chemicals without protective coating — corrosion resistance is poor.

5052-H32 — Forming and Marine Corrosion Resistance

5052-H32 is the strongest common non-heat-treatable alloy (228 MPa tensile / 193 MPa yield). Its magnesium chemistry delivers outstanding resistance to salt water and industrial atmospheres, plus excellent formability — which is why it is the default material for bent fabricación de chapa metálica rather than heavy machining. On the mill it cuts “gummy” compared to 6061, so pure CNC parts rarely start from 5052 plate. Choose it for fuel tanks, marine panels, and any part that combines Doblado with light machining.

Mejor para: Chapa Metálica parts, marine/chemical environments, formed-then-machined hybrids.
Avoid when: the part is fully machined from billet with tight finish requirements — 6061 machines cleaner.

6082-T6 — The European Structural Standard

6082-T6 is the European (EN) counterpart to 6061 and the highest-strength alloy of the 6000 series, with 310 MPa tensile and 250–260 MPa yield strength plus slightly better corrosion resistance. German, Dutch, and Italian engineering drawings routinely call out 6082 (or its DIN name AlSi1MgMn / 3.2315) for machine frames, guide rails, and structural components. If your drawing specifies 6082 and your supplier only stocks 6061, the two are interchangeable in most static Aplicacións — but confirm with your engineer before substituting on certified structural parts.

Mejor para: EU-specified structural and machine-building parts; direct 6061 alternative.
Avoid when: sourcing in North America or Asia where 6061 is cheaper and more available — substitute after engineering sign-off.

Velocidades de corte y parámetros de mecanizado para aluminio

Aluminio’s low cutting resistance lets carbide tooling run at surface speeds that would destroy tools in steel. Typical shop parameters with solid carbide end mills:

Operation	Surface Speed (SFM)	Surface Speed (m/min)	Notes
Roughing (6061, 6082)	800–1,000	244–305	2–3 flute end mill, full coolant
Acabadoing (6061, 6082)	1,000–1,500	305–457	Mayor speed improves finish
2024 / 7075 (harder grades)	800–1,500	244–457	Chips break cleanly, watch tool wear
High-speed machining (HSM)	2,000–3,000+	610–915+	Requires 15,000+ RPM spindle

What this means for buyers — three things your machinist wishes you knew:

• Chip evacuation limits speed more than the material does. Deep pockets with small cutters force slower feeds. Diseñoing pocket depth under 3–4× tool diameter keeps cycle time (and price) down.
• 2–3 flute tools are standard for aluminum. The large flute valleys clear the soft, voluminous chips. This is also why aluminum parts quote faster than steel — more material removed per minute.
• Thin walls chatter. Below ~0.8 mm Espesor de pared, aluminum deflects under cutting force, requiring slow finishing passes. Keep walls at 1 mm+ where the design allows.

Opciones de acabado superficial para piezas de aluminio CNC

Surface finish has two layers: the as-machined roughness left by the cutter, and any Post-Procesamiento applied afterward. Specify both on your drawing — they are priced separately.

As-Machined Roughness Grades

Per ISO standards, Ra 3.2 µm is the default as-machined finish for CNC work — visible tool marks, fully functional for most industrial parts. Ra 1.6 µm adds a finishing pass for mating and sealing surfaces. Ra 0.8 µm requires slower feeds and sometimes Pulido, reserved for bearing seats, O-ring grooves, and optical fixtures. Each step roughly doubles the finishing effort, so apply tight callouts only to the surfaces that need them — the same logic that applies to tolerance standards.

Post-Procesamiento and Coating Options

Acabado	Espesor	Propósito	Notes for Aluminio
anodizado Type II (MIL-A-8625)	1.8–25 µm	Corrosion protection + color (any dye)	Excelente on 6061/6082/5052; slight yellow tint on 7075
anodizado Type III (hardcoat)	13–150 µm (typ. ~50 µm)	Wear resistance — surface harder than tool steel	Usually left undyed/unsealed; affects tight Tolerancias (~50% builds outward)
Granallado con perlas	—	Uniform matte texture, hides tool marks	Standard prep before anodizado for cosmetic parts
Chromate conversion (Alodine)	<1 µm	Corrosion protection + electrical conductivity	Keeps grounding paths conductive — anodize no
Recubrimiento en polvo	60–120 µm	Thick colored protective layer	Cheaper than anodizado for large parts; less precise

Two specification traps worth knowing: Type III hardcoat grows the part — roughly half the coating thickness builds outward, so a Ø10.000 mm pin with 50 µm hardcoat becomes ~Ø10.050 mm. Machine undersize or note “dimensions apply after coating” on the drawing. And anodizado is an insulator — if your enclosure needs EMI grounding, mask the contact points or switch those faces to chromate conversion.

Cómo elegir el grado de aluminio adecuado para su pieza

Work through these five questions in order — they resolve 95% of grade decisions:

1. Is the load case demanding? Run the numbers first. If stresses stay under ~180 MPa with a reasonable safety factor, 6061-T6 works. Only genuine high-stress, weight-critical parts justify 7075’s premium.
2. Will the part be welded? Yes → 6061, 6082, or 5052. 7075 and 2024 are effectively non-weldable in Producción.
3. What is the operating environment? Salt spray or chemicals → 5052 or 6082, or plan for Type II anodizado on 6061. Avoid bare 2024 outdoors.
4. Does it need cosmetic anodizado? Consistent clear or colored finish → 6061/6082/5052. 7075’s copper content shifts clear coatings toward yellow.
5. Is the drawing European? EN/DIN callouts like AlSi1MgMn or 3.2315 mean 6082 — confirm substitution rules before quoting 6061.

Real-world example: a European client sent us a robotics mounting plate specified in 7075-T6. DFM review showed peak stress at barely one-third of 6061’s yield strength. Switching to 6061-T6 cut the material cost by more than half, improved the anodized appearance, and shortened lead time because plate stock was locally available. One material conversation, submitted with the technical drawing package, saved the project meaningful budget with zero performance impact.

Errores Comunes al Especificar Piezas de Aluminio Mecanizado

1. Defaulting to 7075-T6 “to be safe.” This is the most expensive single-line decision on an aluminum drawing. 7075 costs 2–3× more than 6061 per kilo, cannot be welded in Producción, and anodizes with a yellowish tint. If your FEA shows peak stresses below ~180 MPa, 6061-T6 handles the load with margin. The material premium on a 200 mm × 150 mm × 30 mm plate can exceed $40 per part — across a 500-piece order, that’s $20,000 spent on strength the part never uses.

2. One blanket Ra 0.8 callout on every surface. A single Ra 0.8 surface finish callout on a non-functional cosmetic face can add 30–50% to machining time for that feature. Acabado cost is per-surface, not per-part. Call out Ra 0.8 only on bearing seats, sealing faces, and O-ring grooves; let the rest default to Ra 3.2. Your machinist will thank you — and your quote will reflect it.

3. Forgetting anodize growth on toleranced features. Type III hardcoat builds ~50% outward from the original surface. A Ø10.000 ±0.010 mm bore with 50 µm hardcoat becomes roughly Ø10.050 mm — blowing the tolerance five times over. Always note on the drawing whether dimensions apply before or after coating. If you need a precise post-coating fit, the machinist must cut undersized to compensate.

4. Specifying 2024-T4 without corrosion protection. 2024 is the most corrosion-prone aluminum grade in common machining use. Its 4.4% copper content gives it excellent fatigue life but terrible environmental resistance. Bare 2024 exposed to humidity or industrial atmospheres will pit within weeks. If 2024 is truly needed for fatigue performance, specify Type II anodizado or at minimum chromate conversion (Alodine) on the drawing. Better yet: check whether 6061-T6 or 7075-T6 with appropriate Tratamiento de superficies can meet the fatigue requirements — both are far more forgiving in service.

5. Soldadura callouts on 7075 or 2024 drawings. Both 7075 and 2024 belong to the 7xxx and 2xxx families — the two aluminum series that are effectively unweldable in Producción. The heat-affected zone loses 50–70% of its original strength and is susceptible to hot cracking during solidification. If the part must be welded, redesign around 6061-T6 (excellent weldability with 4043 or 5356 filler) or 5052-H32. If the part must be 7075, eliminate the weld joint — use fasteners, press-fits, or adhesive bonding instead.

6. Mixing grade standards without checking regional availability. A drawing that calls out 6082-T6 (the European EN standard) sent to a North American shop will often be quoted in 6061-T6 with an upcharge for “special order” material — even though the two are functionally interchangeable in most static Aplicacións. Conversely, 6061 is uncommon in European stockists. When sending RFQs internationally, note acceptable substitutions: “6061-T6 or 6082-T6 per availability” can save 10–15% on material line items.

Frequently Asked Questions Acerca de CNC Aluminio Machining

What is the best aluminum grade for mecanizado CNC?

6061-T6 is the best all-around choice for roughly 80% of CNC machined aluminum parts. It offers an excellent balance of strength (310 MPa tensile), machinability, weldability, corrosion resistance, and cost. For high-stress aerospace or motorsport components, 7075-T6 provides nearly double the yield strength at 2–3× the material cost. For Chapa Metálica parts that require Doblado, 5052-H32 is preferred. The “best” grade always depends on your specific load case, environment, and budget — which is why we include free grade recommendations with every DFM review.

How much does CNC aluminum machining cost?

Aluminio mecanizado CNC costs are driven by three factors: material (6061 plate stock typically $3–6/kg, 7075 roughly 2–3× that), machine time (aluminum cuts 3–4× faster than steel, so hourly rates go further), and Post-Procesamiento (anodizado adds $0.50–2.00 per part depending on size and Type). A simple bracket in 6061-T6 might cost $8–25 per part at prototype quantities, dropping significantly at Producción volumes. For an accurate quote, send your CAD file and specify the grade, quantity, and any finish requirements — we respond within 24 hours.

What surface finishes are available for CNC aluminum parts?

The most common finishes for machined aluminum are: As-machined (Ra 3.2 µm default, visible tool marks), anodizado Type II (1.8–25 µm, corrosion protection + color options), anodizado Type III hardcoat (13–150 µm, wear resistance — surface becomes harder than tool steel), Granallado con perlas (matte texture, hides tool marks), Chromate conversion/Alodine (thin chemical film for corrosion + electrical conductivity), and Recubrimiento en polvo (60–120 µm colored protective layer). Most industrial parts ship with either as-machined or Type II anodized finish.

Can 7075 aluminum be welded?

No — 7075-T6 is considered non-weldable in Producción. The heat from Soldadura destroys its carefully engineered precipitation-hardened microstructure, leaving the weld zone with 50–70% less strength than the parent material. Worse, 7075’s high zinc and copper content makes it susceptible to hot cracking during weld solidification. If your design requires Soldadura, switch to 6061-T6 (welds excellently with 4043 or 5356 filler rod) or redesign the 7075 part to use mechanical fasteners, press-fits, or adhesive bonding instead of welds.

What Tolerancias can CNC aluminum machining hold?

Standard CNC aluminum machining holds ±0.05 mm (±0.002 in) without special effort. With careful setup, ±0.01 mm (±0.0004 in) is achievable on critical features — but this tightens with part size. A 500 mm long aluminum plate will move more under cutting forces and thermal expansion than a 50 mm bracket. For reference, our standard tolerance is ISO 2768-m (medium), and we routinely deliver ±0.02 mm on aluminum parts under 300 mm. Always specify only the Tolerancias that affect function — blanket tight callouts are the fastest way to inflate a quote. See our mecanizado CNC Tolerancias guide for more detail.

Consigue tus piezas de aluminio mecanizadas correctamente a la primera

{ “@context”: “https://schema.org”, “@type”: “FAQPage”, “mainEntity”: [ { “@type”: “Question”, “name”: “What is the best aluminum grade for mecanizado CNC?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “6061-T6 is the best all-around choice for roughly 80% of CNC machined aluminum parts. It offers an excellent balance of strength (310 MPa tensile), machinability, weldability, corrosion resistance, and cost. For high-stress aerospace or motorsport components, 7075-T6 provides nearly double the yield strength at 2-3× the material cost.” } }, { “@type”: “Question”, “name”: “How much does CNC aluminum machining cost?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “Aluminio mecanizado CNC costs are driven by material (6061 plate stock $3-6/kg), machine time (aluminum cuts 3-4× faster than steel), and Post-Procesamiento (anodizado $0.50-2.00/part). A simple 6061-T6 bracket costs $8-25 at prototype quantities, dropping at Producción volumes.” } }, { “@type”: “Question”, “name”: “What surface finishes are available for CNC aluminum parts?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “Common finishes include: As-machined (Ra 3.2 µm), anodizado Type II (corrosion + color), Type III hardcoat (wear resistance), Granallado con perlas (matte texture), Chromate conversion/Alodine (conductivity), and recubrimiento en polvo (thick colored layer). Most industrial parts ship as-machined or Type II anodized.” } }, { “@type”: “Question”, “name”: “Can 7075 aluminum be welded?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “No, 7075-T6 is non-weldable in Producción. Soldadura destroys its precipitation-hardened structure, leaving 50-70% strength loss in the weld zone, and its high zinc/copper content causes hot cracking. Use 6061-T6 for weldments or redesign 7075 parts with fasteners/press-fits.” } }, { “@type”: “Question”, “name”: “What Tolerancias can CNC aluminum machining hold?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “Standard CNC aluminum machining holds ±0.05 mm without special effort. ±0.01 mm is achievable on critical features but tightens with part size. Our standard is ISO 2768-m, routinely delivering ±0.02 mm on parts under 300 mm. Specify only Tolerancias that affect function to avoid inflated quotes.” } } ] }

Grade selection, cutting strategy, and finish specification decide most of an aluminum part’s cost before a single chip is cut. If you’re unsure between 6061 and 7075 — or whether your finish callouts are adding silent cost — send us your drawings. BravoFabs machines aluminum parts daily for industrial clients across Europe and North America, and every RFQ includes a free DFM review with grade and finish recommendations.